Seachrome Bench Style 28" x 15" Shower Seat | Swing Down Legs | SSB2-280150

$450.85
$368.00
(You save $82.85 )
(No reviews yet) Write a Review
SKU:
SSB2-280150

Seachrome Bench Style 28" x 15" Shower Seat | Swing Down Legs | SSB2-280150

A convenient bench seat that provides secure support in the shower, and easily folds against the wall when not in use. It features swing-down legs that raise the seat to the 17-19" minimum height required to meet ADA regulations. Choose from a range of material and finish options.

 

STANDARD SEAT MATERIALS/COLORS

Naugahyde – White or Almond, covering 2” (51mm) thick foam mounted on 1/2” (13mm) thick marine plywood.

Phenolic – White or Teak, 1/2” (13mm) thick x 3” (76mm) wide slats bolted to frame with countersunk stainless steel screws.

Phenolic Solid – White or Teak, solid 1/2” thick single seat top with slots for drainage.

HDPE (High Density Polyethylene) – White, 1/2” thick one piece.

Solid Surface – Various Colors, 1/2” thick solid surface material.

SPECIFICATIONS

Seachrome seats meet Federal Spec. WW-P-541/8B and ANSI 117.1. When properly installed, all seats exceed applicable federal load specifications. These models have been independently tested to withstand 1,000 lbs in a 30-minute static load test.

NOTE: Seachrome recommends that all accessibility seats, as well as grab bars, be installed using 2” minimum thickness “in-wall” solid wood backing material with #10 x 2” stainless steel, Phillips head, sheet metal screws, or using a wall-imbedded minimum 12 gauge (2.8mm) steel anchor plate with #10 x 24 stainless steel machine screws.

Load Bearing and Installation:

When properly installed, all Seachrome shower seats have been designed and manufactured to support loads exceeding the downward pull requirements for Federal specifications FHA, VA, HUD, hospital codes, and private construction. The actual "in use" load bearing capacity of any shower seat, however, will be limited by the strength of its mounting surface and installation hardware. Seachrome recommends that shower seats be installed using 2" minimum thickness "in wall" solid wood backing material with #10 x 2" stainless steel, phillips-head, sheet metal screws, or using a wall embedded, minimum 12 ga. (2.8mm) steel anchor plate with #10 x 24 stainless steel machine screws. Please contact the factory for further mounting recommendations.
Under no circumstances should any shower seat be mounted to drywall, sheetrock, plaster, fiberglass, acrylic or other similar "hollow" wall surfaces without appropriate wood or steel backing material.

 

  • Seat top material options:Seat top design:  3" slats (phenolic material only) or one-piece solid with standard drain slots
    • Phenolic material, offered in Almond, Teak or White
    • 1-1/2" cushion, offered in Almond or White
    • One-piece solid HDPE (White)
    • Solid Surface material (9 standard options)
  • Frame:  constructed from #304 stainless steel, 1-1/4 square x 18 gauge, .048 with flanges (3" diameter x 10 gauge, .135), welded to tubing (1" diameter x 18 gauge, .048)
  • Swing-down legs: #304 stainless steel, 1" diameter x 18 gauge, .048, adjustable to 17-19" height
  • Legs automatically lock in place when seat is raised up
  • Available frame finishes: Satin Stainless, Polished Stainless, Powder Coat (9 standard colors: White, Biscuit, Almond, White Wrinkle, Almond Wrinkle, Satin Nickel, Bronze, Black, Polished Brass)
  • Supports in excess of 900 lbs. when properly installed

 

Specifications:

https://seachrome.com/file_downloads/SSB2-240150-HW.pdf

 

A convenient bench seat that provides secure support in the shower, and easily folds against the wall when not in use. It features swing-down legs that raise the seat to the 17-19" minimum height required to meet ADA regulations. Choose from a range of material and finish options.

 

Product has no reviews please write a review Write a Review

Related Products

Customers Also Viewed